The washing machine is a beautiful appliance and needs a little bit of care for its proper functioning and long life.
The main inlet and outlet of water are provided by washing machine hoses, and they have to be of good quality to avoid any leaks or bursts.
Washing machine hoses are usually hidden from view, and we notice them only when there is a leak. It is necessary to check them at regular intervals so that you can see any leaks or damages in time.
Also, keep track of how old the washing machine hose is so that you can change it before any damage happens.
There can be many reasons for washing machine hoses to start leaking or bursting. One apparent reason is the sheer age factor.
The material of the hose deteriorates in time and will cause it to weaken and cause a leak. This aging is usually hastened by the chemical contents in the water and detergents that pass through the hose.
Also, many times, the hoses are not drained fully, and some water will be left behind, which causes the chemicals to act faster on the hose. The pumping action in the machine should be adequate to drain out all the water from the hose, or a separate pump can be installed.
Another primary reason seen for damages in washing machine hoses is improper installation.
A sharp bend in the hose or at the connectors will shorten the life of any type of hose.
A distance of at least 4 inches should be there between the wall and the rear of the machine, which will prevent any undue pressure on the connector part of the hose.
If space is tiny, then going in for a right-angled connector would be a good option. These are available in the market and will provide the sharp bend which is needed, without damaging the hose.
If you are planning to replace your washing machine hose, you will be confronted with two possible choices; the stainless steel braided hose and the reinforced rubber.
The stainless steel braided hoses are much stronger and have the inner plastic hose encased in a stainless steel mesh. They are more resistant to any cuts or twists in comparison to the rubber hoses.
The reinforced rubber hoses have been there for a long time and now come with a casing of a mesh of polyester or rayon, which gives them more strength against bursting.
The correct installation of washing machine hoses will save a lot of headaches in the future.
Check the rear area of the washing machine and wall for any sharp edges or points sticking out. The installation of the hose should be without any twists or sharp bends. Especially the connectors should have a reasonable leeway without any pressures created by bends.
The back of the washing machine area should not be moist or wet, which can lead to rusting of the connectors. Changing washing machine hoses is a simple procedure and can be completed within an hour.
Washing Machine Hose Extension Solves The Problem Of Short Hose
Many washing machines are shipped with rather a short hose that is not enough for your conditions. However, it is not required to replace it.
All you need to do is to extend it with a particular washing machine hose extension. This will be a much simpler solution that you can apply in your own hands.
Removing a hose from a washer means much more effort than merely extending it to a size you need. Just attaché the extension to a native hose with the help of an exclusive clamp and put it send wherever you need.
When you choose a hose extension online, make sure it suits your washing machine model. Also, buy an extension of proper length that will be enough for your purposes.
Starting its installation, disable the washer from the water supply. Move the washer away from the wall to reveal its back and reach the drainage hose.
Mention that the extension kits recommended by washer manufacturer are the longest possible ones for your washer. If it is not enough, all you can do is to relocate your washer.
You need to push the washing machine hose extension into the washer’s hose. Push it as deep as you can to fasten it tightly. This will help to avoid any water leakage.
The washer usually vibrates and can even move when working, so tight connection is a must-be feature.
The next step is placing the hose clamp to the end of the hose, just above the extension. Tighten it properly, according to the instructions in the extension kit.
Put the extension to the proper position and move the washer to the location you need. Connect it to the water supply and make a test wash cycle to make sure everything is connected correctly. If there is no leakage, you’ve done everything correctly.
Usually, extension kits are sold together with detailed pictured instructions, so there are no problems when installing it.
There are a few kinds of extensions available – rubber, plastic, and metal. You can choose any you wish, rubber is the most flexible ones, while metal is the most durable.